THSP symbol

Engineered Stone Silica Dust: HSE Inspection Crackdown Begins Now

HSE inspectors are visiting fabrication businesses. Over 1,000 inspections are planned between May 2026 and April 2027, with enforcement action taken where required. This may include prohibition notices, improvement notices, or prosecution.

Businesses failing to meet required standards face enforcement action, which may include prohibition notices, improvement notices, or prosecution.

HSE Deputy Director Mike Calcutt has been direct “The guidance is now published, the expectations are clear, and our inspectors are coming. Those who are cutting corners are not just putting their workers at risk, they are undercutting the businesses doing things properly.”

 

What Has Happened?

On 11 May 2026, the Health and Safety Executive (HSE) announced its most significant intervention in the engineered stone sector to date. Following the deaths of two young workers from silicosis, and two years of research and industry engagement, the HSE has published landmark new COSHH guidance and launched a nationwide enforcement campaign.

The new guidance, Working Engineered Stone: Control Silica Risk, is the first-ever COSHH guidance sheet specifically for the engineered stone sector. It sets out in plain terms what is now expected of every employer working with this material to comply with their legal duties.

This campaign is enforcement-led, with inspections already underway and clear expectations placed on dutyholders across the industry.

 

Why This Matters: The Silica Dust Risk

Engineered stone, widely used in kitchen and bathroom worktops, can contain up to 95% crystalline silica. When cut or polished, it releases respirable crystalline silica (RCS) dust, invisible to the naked eye, which penetrates deep into the lungs and can cause silicosis, chronic obstructive pulmonary disease (COPD), and lung cancer.

Critically, dry cutting of engineered stone results in RCS exposure levels five to ten times higher than wet cutting methods using the same tools. [msn.com]

Unlike traditional silica-related illnesses, which may take decades to develop, exposure to engineered stone dust can cause severe and irreversible lung damage within months or years. Workers can suffer permanent damage before experiencing any symptoms.

Silicosis from engineered stone has been shown to develop far more rapidly than from natural stone exposure, with severe cases occurring in relatively short exposure periods.

The Legal Requirements: What You Must Do

These are not recommendations. They are legal obligations under COSHH regulations. Employers must:

  • Switch, where reasonably practicable, to engineered stone products with a lower silica content. Lower-silica alternatives are available at equivalent quality.
  • Use on-tool water suppression during all cutting operations and control airborne mist. This is the recognised method of complying with legal exposure control requirements.
  • Provide appropriate respiratory protective equipment (RPE) for all workers involved in cutting, grinding, or polishing.
  • Carry out regular health surveillance for workers exposed to RCS dust.

Dry cutting of engineered stone is unacceptable and must not be undertaken under any circumstances. This practice does not meet legal control requirements.

Your Action Checklist

  • Stop dry cutting. All dry cutting of engineered stone must cease immediately. This is declared unacceptable by HSE and constitutes a breach of COSHH requirements.
  • Review your stone products. Audit the materials you use and assess silica content where information is available. Switch to lower-silica alternatives where reasonably practicable.
  • Install wet suppression. Ensure on-tool water suppression is in place and functioning on all cutting equipment, with airborne mist effectively controlled.
  • Check and issue RPE. All workers involved in cutting, grinding, or polishing must have appropriate respiratory protective equipment and be trained, face-fit tested, and supervised in its correct use.
  • Set up health surveillance. If you do not already have a programme in place for workers exposed to RCS, this must be established without delay.
  • Review your COSHH assessments. Ensure your assessments are up to date, reflect the new guidance, and specifically address the risks from engineered stone silica dust.
  • Ensure controls are applied in practice. Put supervision arrangements in place to ensure controls are consistently followed, including during any on-site installation or modification work.

This applies to all businesses involved in fabrication, processing, or installation of engineered stone, including any site-based cutting activities.

Designers, specifiers, and clients should also consider the risks associated with engineered stone and, where possible, specify lower-silica materials to reduce exposure across the supply chain.

 

How THSP Can Help

If your business works with engineered stone, you should act on this guidance immediately. We can support you with COSHH assessment reviews and updates, RPE selection and health surveillance programme setup, on-site compliance audits ahead of HSE inspection, workforce training on safe working practices and dust control, and advice on sourcing lower-silica engineered stone products.

Contact your Account Executive if you want to review your arrangements or discuss your requirements.

03456 122 144

enquiries@thsp.co.uk

www.thsp.co.uk